Fire Extinguisher Training - There are four classes of fire extinguishers. Each one is designed for a specific type of fire. Modern fire extinguishers use a picture and labeling system to designate which types of fires they are designed for. Older units use colored geometrical shapes with letter designations.

Class A and B fire extinguishers have a numerical rating based on tests conducted by Underwriter’s Laboratories. These ratings determine the extinguishing potential for each size and type of extinguisher.

Class A Extinguishers will put out fires in ordinary combustibles such as wood and paper. The numerical rating refers to the amount of water the fire extinguisher holds and the amount of fire it is designed to extinguish.

Class B Extinguishers are used on fires involving flammable liquids like grease, gasoline, oil, etc. The numerical rating states the approximate number of square feet of a flammable liquid fire that can be extinguished.

Class C Extinguishers are for use on electrical fires. This class of fire extinguishers does not have a numerical rating. The presence of the letter “C” indicates that the extinguishing agent is non-conductive.

Mirror Ceiling Tile - Planning and good layout are the most important parts of a successful ceiling tile job. Once everything is laid out, the project should go smoothly. And it's also one of those tasks that adds a lot of appeal to your home.

Selecting the Tiles

Most ceiling tiles are made of fiberboard. Standard tiles measure 12" by 12", although tiles are also made in 12" by 24" and other sizes. Acoustical tiles are made from the same type of fiber with an additional manufacturing process to help absorb sound in a room. A well designed acoustical tile absorbs up to 70 percent of excess noise.

Ask the supplier to help estimate the materials you need for installation. Most manufacturers provide charts to determine the number of tiles, the amount of furring, and the gallons of adhesive needed (if adhesive is used) based on the room size. Tiles are typically packed as follows: 12" by 12" ceiling tiles in cartons of 40, 12" by 24" are packed 20 to a carton.

Ceiling Tile Installation Methods

The most common methods of ceiling tile application are adhesives, stapled or nailed to wood furring strips, or a metal grid suspended from the overhead floor joists. For ceilings made of plaster, sheetrock, or other materials that provides a smooth, continuous backing, use adhesives to apply the ceiling tiles. If the ceiling has cracked plaster or other defects, apply furring strips and nail or staple the tiles to the furring strips.

Basic Rules

• All cut tiles should be used for the edges of the room where the ceiling meets the walls.

• Cut tiles at opposite ends of the room should be the same size.

• If at all possible, cut tiles should not be less than half a tile wide.

Determine the Size of Border Tiles

Measure the distance from wall to wall on the longer side of the room. If the length measures exact feet, you will not need to cut border tiles for that direction. If the distance does not come out in exact feet, add 12 to the number of inches remaining and divide by two. This gives you the width of your border tiles. For example, if the room is 10′ 6" long, add 12 to 6 (18) and divide 18 by 2. The result of 9" is the width of the border tiles for each end of the run. Do the same thing for the shorter side of the room. Confused? Here is the result of the calculations:

• 10′ 6"
  

  More >>

Ranch House Plan - Building your own home is both rewarding and maddening. The problems you will face can tax both your energy and patience. Even hiring a general contractor to manage the project will not prevent problems from distracting you from other activities (like making a living).

You will also face one of the most frustrating things you likely will ever come across - the local building inspector. Just wait until one of these creatures shows up at your building site. You won't believe the goofy things they come up with. To be fair, some of the items they refuse to pass will be valid. But all too often, you'll end up with a jackass that's trying to stroke his/her over inflated ego.

Don't count on anybody to do their job right. Just because an architect has a nice office and a good reputation doesn't mean the drawings will be done properly. The contractor that comes highly recommended might end up ripping you off with shoddy work. You absolutely must stay on top of the entire home building project to prevent losing money or getting a house that you hate. It's amazing how many contractors can't even read a simple set of blueprints. And don't let them talk you into changing something unless you really want the change. In some cases, the contractor is simply trying to swap cheaper materials to increase the profit margin.

Get a firm estimate, put everything in a contract, and hold everybody to it. Don't allow excessive monetary draws. While it's customary to have an initial draw, make sure it's for actual building expenses and not some kind of "fee" to get work started. Every dime should go towards actually building the house. While material costs vary, and there is usually a clause in the contract that allows for this, don't fall for the "I'm not making any money on this project" scam three quarters of the way through. Unless you have made changes to the original plan that increase the cost, or supplies go up more than anticipated, don't pay any more than stated in the contract. Pay a dollar for a dollar, nothing more, nothing less. If you have been keeping the draws under control you can fire the contractor if necessary and find someone else. Remember that it's your house, your money, and you are the boss.

Tin Roof - Most people pay very little attention to the roof on their home. Since it has no moving parts to wear out, there doesn’t seem to be anything that needs attention. But that’s not true. Your roof is the first line of defense against sun, wind, rain, snow, hail, and a host of other assaults. Blocked gutters can allow water to get under the roofing shingles, damaging the underlayment.

Your roof must be inspected periodically to ensure minor problems are corrected before real damage sets in. If the pitch of your roof is low, and you are comfortable (and confident) walking around on it, you can perform your own inspection and make small repairs yourself. Otherwise, hire someone to do this for you. Be careful - a fall, even from a single story house, can be fatal.

Here are some reasons why roofs fail:

Inadequate Maintenance - Ignoring small problems is the single greatest reason for premature failure of roofing systems. Catching small damage early and making repairs is vital to longevity. Waiting until water is dripping inside the house is a great way to unnecessarily spend a lot of money. By the time you notice a leak, the damage has most likely spread well beyond the original problem area.

European House Plan - Before ordering a set of house plans, you need a clear picture of what you want. Two story or one? Attached garage? How many beds and baths? Large family room? Take a tour of homes, read books and magazines. Make a list of "must-haves" and "would like to haves". Look at floor plans. Start a notebook with information and notes on all the details you want to include.

This also might be the time to weigh hiring a building professional, under a management contract, to help you. This person would cost less than a general contractor, and could walk you through parts of the project where you feel inexperienced.

As the manager, your biggest responsibility is hiring the subcontractors who will do the work. Do you know someone that recently had work performed on their house? Who did they use? Was it done on time and within budget? Would they use them again.

Drive around neighborhoods you like and find out who's building the houses. If you have dealt with subcontractors in the past (and you trust their opinion), get recommendations from them. If your carpenter recommends an electrician he works with frequently, that's a solid lead.

Once you get names, you want to learn all you can. Get a list of references and talk to them. Examine past work in person. Arrange to meet them on a current job site. When you find subcontractors you like, start writing down the work quotes. And remember that the low bidder doesn't necessarily do the best work.

Concrete Mixer - Cracked sidewalks and driveways can have a negative effect on the look or your home. And the damage tends to worsen with time due to water getting under the structure. Fortunately, repair is not too difficult.

Cracks in Sidewalks

Enlarge the crack along its entire length with a cold chisel and hammer. Use gloves and eye protection! Make the crack wider at the bottom than at the top, a process known as undercutting. It helps to bond the new concrete with the older concrete. After the crack has been thoroughly undercut, remove all loose material and brush the area with a wire brush.

The new concrete patch will hold better if a concrete adhesive is used first. This will both assist with bonding and prevent old concrete from absorbing moisture from the newly installed patch. Brush the adhesive into the undercut area and allow it to dry until it becomes tacky.

Use one part Portland cement to 2 1/2 parts of fine, clean sand. Heavier concrete patch jobs call for one part of Portland cement to two parts of sand and three parts of gravel. Building supply centers sell pre-mixed concrete for this type of job. All you add is water and it makes things much easier than buying and mixing the ingredients yourself.

Carpet Tile - Carpet is one of those home items that's generally taken for granted. Most homes built today have carpet in the majority of rooms. Homeowners don't usually pay much attention to their carpet until it's worn and time for replacement. Then the choices of material and pile type can be very confusing.

Carpets are made by pulling loops of yarn through a tough backing. These loops are often cut to create the carpet's pile. The most durable synthetic carpeting material is nylon. It wears well and is quite stain resistant.

The list of synthetic fibers can be confusing because manufacturers often call them by proprietary names. Still, all synthetics fall into four generic categories: nylon, olefin, acrylic, and polyester.

Nylon - The majority of carpet fibers are made of nylon. Nylon fibers are resilient, survive the weight of furniture, and hold up well in heavily trafficked areas. Nylon is available in a vast array of colors, and solution-dyed types are colorfast. Nylon carpets can be found in a wide variety of wear ratings and price ranges. This is generally the best choice of carpet fiber for the home.

Olefin - Also known as polypropylene, olefin is another popular choice for carpet. It is easy to clean, strong, and resists stains and wear. Olefin is used mostly in Berbers and commercial carpets. Color is added before the material is turned into fiber, making it colorfast. Olefin carpet is comparable in price to nylon.